Salt-affected soils cover more than 400 million hectares worldwide (FAO, 2021), and saline and sodic soils need opposite first steps. This guide covers salinity (osmotic stress) versus sodicity (clay dispersion), how to read EC, ESP and SAR and the four soil classes, how irrigation without drainage, salty water, land clearing and seawater make land salty, reclaiming saline soil by drainage and leaching, the threshold-and-slope yield loss with a wheat example and a salt-tolerance list, reclaiming sodic soil with gypsum or acid-forming amendments, a worked gypsum requirement, saline-sodic soils and using salty irrigation water.
Saline, sodic and saline-sodic soils, and their reclamation →
White crusts on the surface.
Patches where the crop never comes up. Water that stands for days after irrigation.
These are signs of salt-affected soil, a problem of dry climates and of irrigation, wherever water evaporates and leaves its salts behind faster than rain or drainage can wash them away.
FAO's global map of twenty twenty-one estimated more than four hundred million hectares of salt-affected topsoil, on every continent:
from the Indus and the Tigris and Euphrates to Central Asia,
the Murray-Darling basin in Australia, the western Americas, the Sahel, North Africa and parts of China.
Here is the key point of this video.
There are two different problems, salinity and sodicity,
and they call for opposite first steps.
Get the order wrong, and you can make a soil worse.
In this video: how to tell them apart, how land becomes salty, how to reclaim each kind, how much yield salt costs, and a worked gypsum calculation.
The advice is general and global. A laboratory test and your local extension service come first.
Salinity means too much soluble salt in the soil water:
chlorides, sulphates and carbonates of sodium, calcium and magnesium.
It harms plants mainly through osmotic stress.
Salty water holds on to its water molecules, so roots must work harder to take it up, and the crop behaves as if it were in drought, even in a wet soil.
Some ions, such as sodium, chloride and boron, can also be directly toxic, especially to fruit trees and vines.
Sodicity means too much sodium held on the soil's clay and humus.
Its main harm is to the soil itself.
Sodium cannot hold clay particles together the way calcium can.
So when the soil is wetted with low-salt water, the clay disperses. The crumbs fall apart, fine particles clog the pores, the surface seals into a hard crust, water stands on top, and roots and seedlings struggle. Sodic soils are also often strongly alkaline, which brings nutrient problems.
You cannot tell reliably by eye, so test.
Salinity is measured as electrical conductivity, because dissolved salts conduct electricity.
The reference method uses the water drawn from a saturated soil paste, in units of decisiemens per metre. Quicker soil-water extracts read lower, and the laboratory converts them.
Sodicity is measured as the exchangeable sodium percentage: the share of the soil's exchange sites held by sodium. A simpler measure, the sodium adsorption ratio, compares sodium with calcium and magnesium in the soil solution or in irrigation water. A ratio of about thirteen corresponds roughly to an exchangeable sodium percentage of fifteen.
The classification most textbooks still use was published by the United States Salinity Laboratory in nineteen fifty-four.
A saline soil has a conductivity above four, with exchangeable sodium below fifteen per cent; it often shows white salt crusts, but keeps a good structure. A sodic soil is the reverse: low salt, sodium above fifteen per cent, a pH often of nine to ten, a dark surface from dispersed organic matter, a hard crust and standing water. A saline-sodic soil has both.
Older books call them white alkali and black alkali.
Some salinity is natural: weathering of salty rocks, old seabeds, sea salt carried on the wind, and closed basins where water leaves only by evaporation. But much of it is caused by people.
The biggest cause is irrigation without drainage.
Every irrigation adds salt. If the water table rises to within a couple of metres of the surface,
water rises through the soil by capillary action and brings salt up into the root zone, so waterlogging and salinity arrive together. Irrigating with salty or high-sodium water, including some groundwater, adds more. Clearing deep-rooted native vegetation raises water tables and mobilises stored salt, which is called dryland salinity, seen widely in southern Australia.
And on coasts, over-pumping lets seawater into fresh aquifers, while storm surges and rising seas flood fields.
Soluble salts can be washed out, but two conditions are essential.
First, drainage.
Water must be able to leave the root zone. Where the water table is high, subsurface drains or deep open drains come first.
Leaching a field with no drainage only raises the water table and brings the salt back.
Second, leaching with good-quality water: enough to dissolve the salts and carry them below the roots.
As a rule of thumb, ponding a depth of water roughly equal to the depth of soil you want to reclaim removes a large share of the salt.
Intermittent ponding uses less water than continuous flooding.
And on land that stays irrigated, add a leaching fraction, a little extra water with each irrigation, to stop salt building up again.
How much does salinity cost?
Crop response is often described by a threshold and a slope:
yield is unaffected up to a threshold conductivity, then falls in a straight line.
For wheat, typical published values are a threshold of about six,
and a slope of about seven point one per cent for each unit above it. In a soil at ten, wheat gives one hundred, minus seven point one times four: about seventy-two per cent of full yield.
Common bean, with a threshold of about one and a slope of about nineteen per cent, would give nothing at all in the same soil.
Thresholds vary with variety, climate and irrigation method, so treat them as guides.
So crop choice matters.
Barley, cotton, sugar beet, date palm and many salt-loving forages are tolerant.
Wheat, sorghum and soybean are moderately tolerant.
Rice and maize are moderately sensitive.
And beans, carrots, onions, citrus and most fruit trees are sensitive.
A sodic soil needs the opposite first step.
Leaching alone does not help: the water hardly gets in, and the sodium is held on the clay, not dissolved in the water. The sodium must first be replaced by calcium, which also pulls the clay back into crumbs.
Only then can it be leached away.
Gypsum, calcium sulphate, is the most widely used amendment.
It is moderately soluble, cheap, and supplies calcium directly. In sodic soils that already contain lime, acid-forming amendments release calcium from that lime: elemental sulphur, which bacteria turn into sulphuric acid, sulphuric acid itself, or iron sulphate. Organic matter, green manures and sugar-factory press mud improve structure,
and as they decompose they help dissolve the soil's own lime.
And growing tolerant crops during reclamation,
such as rice in ponded fields, sesbania, or salt-tolerant grasses, keeps the land productive while their roots open up the soil.
Gypsum also brings the pH down, indirectly.
It converts sodium carbonate into calcium carbonate and sodium sulphate, which is leached. On a normal acid soil, gypsum does not change the pH.
How much gypsum? Here is the worked example from Laisha's explainer. A sodic soil has an exchange capacity of twenty centimoles per kilogram,
and an exchangeable sodium percentage of forty. The aim is to bring the top fifteen centimetres down to ten per cent. The sodium to replace is forty minus ten, which is thirty per cent of twenty:
six centimoles per kilogram. Each centimole needs zero point eight six grams of gypsum per kilogram of soil, so that is about five point two grams per kilogram. One hectare of soil to fifteen centimetres weighs about two point two five million kilograms.
So you need about eleven point six tonnes of pure gypsum per hectare, or about fourteen and a half tonnes of agricultural gypsum at eighty per cent purity, applied before the leaching water. In practice it is often applied in stages, with an efficiency factor added, because not all the calcium exchanges.
A saline-sodic soil is the trap. It looks saline, so it is tempting to leach it straight away. But the salts are what keep its clay together.
Leach it with good water before replacing the sodium,
and the clay disperses and the soil turns sodic.
So treat it like a sodic soil: gypsum first, then leach.
Can salty water ever be used for irrigation?
Often, with care: tolerant crops, a leaching fraction, good drainage, irrigation methods that keep the root zone moist, such as drip, and blending with better water. The water's conductivity and its sodium adsorption ratio together decide the risk, so have your irrigation water tested as well as your soil.
To recap.
Saline soils have too much soluble salt, conductivity above four, and suffer osmotic stress, but keep a good structure:
drain first, then leach.
Sodic soils have too much exchangeable sodium, above fifteen per cent, with dispersion, crusting and a high pH:
replace the sodium with calcium, gypsum or sulphur in limy soils, then leach.
Saline-sodic soils need gypsum before leaching, or they turn sodic.
Most human-made salinity comes from irrigation without drainage and rising water tables.
Choose tolerant crops while you reclaim, and test both soil and water.
For the full explainer and our crop guides, visit laisha.ai. Thank you for watching.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
An AI operating system for agriculture: free guides, manuals and tools written for every country.