ICAR AIEEA-PG — Agricultural Engineering & Technology (Major Subject Group 10) · India · National Testing Agency for ICAR
Original practice questions written to the published syllabus · not past papersSoil as an engineering material: its phases, flow of water through it, compaction, consolidation, shear strength and stability.
In the exams: GATE AG Section 4 (soil mechanics asked in 6 of 8 papers 2019–26); ICAR AIEEA-PG Unit IV; NCEES PE soils and foundations
ICAR AIEEA-PG — Agricultural Engineering & Technology (Unit IV)
Single-answer MCQs mixing definitions and short calculations: classification symbols and limits, Proctor test details, zero-air-voids line, consolidation time factors, cu = qu/2, Ka and Kp, the failure-plane angle, and Terzaghi bearing capacity terms.
How our questions for ICAR AIEEA-PG spread across the units of Soil Mechanics. Difficulty: 41 easy, 33 medium, 6 hard.
| Phase relations | 10 | |
| Index properties and soil classification | 10 | |
| Permeability | 8 | |
| Compaction and the Proctor test | 8 | |
| Terzaghi one-dimensional consolidation | 8 | |
| Earth pressure: active and passive (Rankine) | 8 | |
| Bearing capacity basics | 8 | |
| Shear strength and the Mohr-Coulomb criterion | 7 | |
| Effective stress | 5 | |
| Seepage and flow nets | 4 | |
| Slope stability, including infinite slopes | 4 |
Choose an answer, then open the working. Each explanation says why the right answer is right and why the others are not.
A soil has a bulk unit weight of 19.0 kN/m³, a water content of 12% and G = 2.65. Taking γw = 9.81 kN/m³, what is its degree of saturation?
B. 0.597
γd = γ/(1 + w) = 19.0/1.12 = 16.96 kN/m³. e = Gγw/γd − 1 = 2.65 × 9.81/16.96 − 1 = 0.532. S = wG/e = 0.12 × 2.65/0.532 = 0.597. Using the bulk instead of the dry unit weight to find e gives e = 0.368 and S = 0.864; 0.318 is just wG with no division by e.
Further reading: Das and Sobhan, Principles of Geotechnical Engineering
A sand deposit has an in-situ void ratio of 0.62. Laboratory tests give a maximum void ratio of 0.85 and a minimum void ratio of 0.45. What is its relative density?
D. 57.5%
Dr = (emax − e)/(emax − emin) = (0.85 − 0.62)/(0.85 − 0.45) = 0.23/0.40 = 57.5%, a medium-dense sand. 42.5% comes from putting emin in the numerator, which measures looseness instead of density. 27.1% divides by emax alone (0.23/0.85), and 72.9% is e/emax (0.62/0.85).
Further reading: Das and Sobhan, Principles of Geotechnical Engineering
In a hydrometer analysis, how long does a spherical particle of diameter 0.01 mm and specific gravity 2.65 take to settle 100 mm in water of viscosity 1.0 × 10⁻³ Pa·s (γw = 9.81 kN/m³)?
B. 18.5 min
Stokes' law: v = (γs − γw)D²/(18μ) = (2.65 − 1) × 9810 × (1.0 × 10⁻⁵)²/(18 × 10⁻³) = 8.993e-05 m/s. Time = 0.1/v = 1112 s = 18.5 min. Using γs instead of (γs − γw) ignores buoyancy and gives 11.5 min; the other options are factor-of-ten unit slips.
Further reading: Das and Sobhan, Principles of Geotechnical Engineering
In a falling-head test, the standpipe area is 1.0 cm², the specimen is 10 cm long with an area of 50 cm², and the head falls from 100 cm to 50 cm in 600 s. What is k?
D. 2.31e-04 cm/s
k = (aL/(At))·ln(h1/h2) = (1.0 × 10)/(50 × 600) × ln 2 = 3.333e-04 × 0.693 = 2.31e-04 cm/s. Using log10 without the 2.303 factor gives 1.00e-04; swapping the standpipe and specimen areas gives an absurdly high 5.78e-01.
Further reading: Das and Sobhan, Principles of Geotechnical Engineering
A sand deposit has a water table 3 m below ground. Above it the sand's unit weight is 17 kN/m³; below it the saturated unit weight is 19.5 kN/m³. With γw = 9.81 kN/m³, what is the vertical effective stress at 8 m depth?
D. 99.45 kPa
σ = 17 × 3 + 19.5 × 5 = 148.5 kPa. u = 9.81 × 5 = 49.05 kPa (water depth is 5 m, not 8 m). σ′ = 99.45 kPa. Measuring u from the ground surface gives 70.02; using γsat above the water table gives 106.95.
Further reading: Das and Sobhan, Principles of Geotechnical Engineering
If the compactive effort applied to a soil is increased, how do its maximum dry density and optimum moisture content change?
D. Maximum dry density rises; optimum moisture content falls
More energy packs the grains more closely with less water needed for lubrication, so the curve moves up and to the left. This is why the modified Proctor test gives a higher maximum dry density at a lower optimum than the standard test.
Further reading: Das and Sobhan, Principles of Geotechnical Engineering
Which assumption underlies Rankine's earth pressure theory?
D. The back of the wall is vertical and perfectly smooth
Rankine assumed a smooth vertical wall so that the stresses in a semi-infinite soil mass in plastic equilibrium apply directly. Wall friction is included in Coulomb's wedge theory; the log-spiral surface is used in more refined passive calculations.
Further reading: Das and Sobhan, Principles of Geotechnical Engineering
What is the steepest slope angle for a long, dry cohesionless embankment face (φ′ = 35°) if a factor of safety of 1.5 is required?
C. 25.0°
F = tanφ′/tanβ, so tanβ = tan35°/1.5 = 0.4668 and β = 25.0°. Dividing the angle directly (35/1.5 = 23.3°) is not the same because tan is not linear. 35° gives F = 1. 46.4° multiplies tanφ′ by 1.5 instead of dividing.
Further reading: Das and Sobhan, Principles of Geotechnical Engineering
A plate load test with a 0.3 m square plate on a deep, uniform dense sand gives an ultimate bearing pressure of 400 kPa. By the usual plate-load relation for sand, what is the ultimate bearing capacity of a 1.5 m square footing at the same level?
A. 2000 kPa
For sand the ultimate capacity from the γBNγ term is proportional to width: qf = qp × Bf/Bp = 400 × 1.5/0.3 = 2000 kPa. 400 kPa (no scaling) applies to clays, where capacity does not depend on width. The test reflects only soil within about twice the plate width, so deeper weak layers must be checked separately. 80 kPa inverts the width ratio (400 × 0.3/1.5), and 10000 kPa squares it (400 × 25).
Further reading: IS 1888; Punmia, Jain and Jain, Soil Mechanics and Foundations
How does compaction differ from consolidation?
D. Compaction expels air quickly by mechanical energy; consolidation slowly expels water from saturated soil under sustained load
Compaction is a rapid densification of partly saturated soil by rolling, tamping or vibration that reduces air voids. Consolidation is the gradual volume decrease of a saturated soil as pore water drains under a sustained load, governed by permeability.
Further reading: Das and Sobhan, Principles of Geotechnical Engineering
Ten here, 80 in the app. The Laisha app has every practice question we have written to ICAR AIEEA-PG in this subject, marked as you go, with timed papers, a jump-to-unanswered list and a certificate when you pass at 70 per cent.
Free for ten days, then one subscription of US$10 a month. We would rather say so here than have you find it later.
An AI operating system for agriculture: free guides, manuals and tools written for every country.