Surveys find that many farm sprayers apply well above or below what their operators believe. This guide covers the boom sprayer formula (L/ha = flow × 600 ÷ (speed × spacing)), why speed matters more than pressure, a seven-step calibration, a full worked example for a 6 m boom, correcting from 160 to 200 L/ha, working out product per tank and granule rates, knapsack calibration with a 100 m² water test, tree row volume for orchard sprayers, nozzle choice and drift control. It closes with Laisha Lens No. 1, our free November guide.
A pesticide label gives a dose per hectare and a spray volume. Whether your crop actually receives that dose depends on the sprayer: how fast it moves, how much each nozzle delivers, and how evenly.
Surveys of farm sprayers in many countries have found that a large share apply well above or below what their operators believe, because of worn nozzles, the wrong pressure, or a guessed speed.
Under-dosing fails to control the pest and encourages resistance. Over-dosing wastes money, risks crop injury and residues,
and harms the environment.
Calibration fixes this, and it takes only a stopwatch, a measuring jug and a tape. In this video: the one formula behind every boom sprayer, a full calibration worked out step by step, how to correct the rate, how much product goes in the tank, knapsack and orchard sprayers, nozzles and drift.
The advice is general and global; the product label always comes first.
For a boom sprayer, the volume applied per hectare depends on three things: nozzle flow, forward speed and nozzle spacing.
The application rate, in litres per hectare, is the nozzle flow in litres per minute, times six hundred, divided by the forward speed in kilometres per hour times the nozzle spacing in metres.
Two consequences matter in the field.
Speed is powerful: double your speed and you halve the volume per hectare.
Pressure is weak: for hydraulic nozzles, flow rises only with the square root of pressure, so doubling the pressure raises flow by only about forty-one per cent, and it also makes the droplets finer.
Nozzle spacing on modern booms is usually fifty centimetres.
Here is the procedure.
One: check the sprayer. Clean the filters and nozzles, check the hoses and the pressure gauge, and use nozzles of the same type and size.
Two: measure your speed.
Mark out fifty or one hundred metres in the field, not on a road, and time the tractor over it in the working gear and engine speed, with the tank about half full.
Speed in kilometres per hour is the distance in metres, divided by the time in seconds, times three point six.
Three: measure the nozzle flow. With the sprayer standing still at working pressure,
collect each nozzle's output for one minute in a measuring jug. Four: check uniformity.
Replace any nozzle whose flow is more than about ten per cent off the average.
Worn nozzles can deliver ten to twenty per cent more than new ones.
Five: calculate the application rate with the formula,
and compare it with the target.
Six: adjust, mainly by speed, or by nozzle size; change pressure only a little.
And seven: set the boom height so the fans overlap correctly,
typically about fifty centimetres above the target for one-hundred-and-ten-degree flat-fan nozzles at fifty-centimetre spacing.
Let us calibrate a six-metre boom with twelve flat-fan nozzles, fifty centimetres apart. The tractor covers fifty metres in thirty seconds.
Fifty divided by thirty, times three point six, is six kilometres per hour.
The one-minute catches range from zero point seven six to zero point eight three litres, with an average of zero point eight. The lowest is five per cent below the average and the highest four per cent above, so all are within ten per cent, and the nozzles are acceptable.
Now the rate.
Zero point eight times six hundred is four hundred and eighty.
Six kilometres per hour times zero point five metres is three.
Four hundred and eighty divided by three is one hundred and sixty litres per hectare.
But the label asks for two hundred litres per hectare. What do you change?
The best option is to slow down.
Rearrange the formula: zero point eight times six hundred, divided by two hundred times zero point five, gives four point eight kilometres per hour. Drive at four point eight, and you apply two hundred litres.
You could raise the pressure instead.
Flow would have to rise from zero point eight to one litre per minute. Because flow follows the square root of pressure, if you are at three bar now, the new pressure would be three times one point two five squared: about four point seven bar. That makes the droplets finer, and may push the nozzle out of its best range. So for a change this big, switching to a larger nozzle size is usually better than turning up the pressure.
Now the product.
With a six-hundred-litre tank at two hundred litres per hectare, each tank covers three hectares.
If the label rate is one and a half litres of product per hectare, each tank needs four and a half litres of product.
Notice what happens if you skipped calibration:
at the real one hundred and sixty litres per hectare, the same tank would cover three point seven five hectares, so a mix made for three hectares would leave you under-dosing.
For granules, work from the active ingredient.
A soil insecticide recommended at one kilogram of active ingredient per hectare, as a five per cent granule, needs one divided by zero point zero five: twenty kilograms of granules per hectare. Always use the label rate for your crop, and only adjuvants that the label permits; the wrong one can injure the crop.
For a knapsack sprayer, mark out a test area, say ten metres by ten metres, one hundred square metres. Spray it with clean water at your normal walking pace and pressure,
and measure how much water you used. If you used four litres, your rate is four litres per one hundred square metres, which is four hundred litres per hectare.
A sixteen-litre knapsack then covers sixteen divided by four hundred:
zero point zero four hectares, or four hundred square metres. So a product used at one litre per hectare needs forty millilitres per knapsack. Keep your walking speed and nozzle height the same in the field as in the test. A lever-operated sprayer gives uneven pressure unless you pump steadily, or fit a pressure regulator, a constant-flow valve.
For tree crops, spray volume is often matched to the canopy using tree row volume.
Multiply tree height by canopy width by ten thousand, and divide by the row spacing, all in metres. Trees three metres tall and two metres wide, in rows four metres apart, give fifteen thousand cubic metres of canopy per hectare. The volume is then set per unit of canopy, which avoids overspraying small trees. Switch off the nozzles where the air stream would miss the canopy,
and set the air volume to reach into the canopy without blowing the spray through it.
Choose the nozzle for the job.
Flat-fan nozzles give an even band, and are standard for boom spraying of herbicides.
Hollow-cone nozzles give fine droplets and good coverage, for insecticides and fungicides on foliage.
Air-induction nozzles make coarse, air-filled droplets that drift much less.
Smaller droplets cover better, but they evaporate and drift onto neighbouring crops, water and homes.
So choose coarser droplets where coverage allows, especially for herbicides.
Spray when the wind is light and steady, not in calm, hot conditions with a temperature inversion.
Keep the boom low and the pressure within the nozzle's range.
And leave buffer zones near water and sensitive areas.
Finally, recalibrate whenever you change nozzles, pressure, speed, the operator or the product.
To recap. Litres per hectare equals nozzle flow, times six hundred, divided by speed times spacing.
Measure speed in the field, catch each nozzle for one minute, and replace any more than ten per cent off. Adjust by speed or nozzle size, because doubling pressure adds only forty-one per cent flow. Work out hectares per tank before you add product. For knapsacks, spray one hundred square metres with water and scale up.
And pick nozzles and weather that keep the spray on target.
For the full calibration guide and worked sums, visit laisha.ai.
And before you go: Laisha Lens number one is out, our free guide to November, for every climate zone on Earth.
North of the equator, the cool-season crops go in:
winter wheat and garlic in the temperate north,
wheat, barley and lentil on the autumn rains of the Mediterranean,
and on the plains of South Asia the whole rabi season,
wheat, mustard, chickpea and potato.
South of the equator it is spring, and the tropical south sows soybean, maize, cotton and rice on the first rains.
Lens also covers crop residue without fire, the pests worth walking the field for, and a study plan for agri students.
Open My farm's November, choose your zone and up to three crops, and it builds your field jobs, week by week, with the pests to scout for. It is free, and needs no account. Our free November Lens, with your farm's month plan, is on laisha.ai slash lens.
From all of us at Laisha: may your fields do well this season. Thank you for watching.
Last updated · How Laisha writes and checks its pages · Report a mistake
US$10 a month · one price worldwide · cancel any time
An AI operating system for agriculture: free guides, manuals and tools written for every country.